Search results

I had these parts (front and rear) re-chromed for my rebuild, then decided to get newer rims that don't allow me to use them. asking only for the cost of the work.$310.00 plus any shipping.

Welcome back to me....I just returned froma year long deployment and am getting back to work on my rebuild. here is my problem...I have 84 Toyota 4X4 pickup that I cannot get toturn over.... I completely stripped down to metal repainted , reinstalled wire harness rebuilt eng tranny new battery...

I forgot to check the orientation of the center bearing and now upon replacement with a new one TZK. I don't know what way faces fwd...there are no markings and it will fit both ways...the only difference appears to be the two hooks on top, Can anyone tell me which way the hooks face...and...

I have hit a roadblock on the total truck rebuild....I have all my front axle parts painted and ready to assemble but now I am in serious need of a TOYOTA SST-09634-60013 so I can align the knucles. Does ANYONE know where I can get one or borrow for a bit. I cannot assemble this without and...

So I'm at the stage of the rebuild where I am stripping down axles (front and rear) for sand blast and Paint/powder coating. I am torn between powder coating and spray painting them ...Any suggestions...My question I have regards the rebuild. I am Not sure which differentials I have, How do I...

Lots happening on the rebuild...1.My block was returned to me with new parts ready to start rebuild (Honest Performance)...rebored +.030 new pistons and complete gasket kit..I will start that after I rebuild my front and rear aXsle and wheel assemblies. also Transmision was returned to me after...

So I get my box off the frame and body shop says probably cheaper to replace than fix the damage to the floor...any body have a good line on a place I can get a decent bed for this rig....Im not having any luck in my search

So I've measured my Bores and they are all 3.642 in. The manual (Haynes) chart shows Bore X stroke should be 3.62X3.5, so I am assuming this has been bored up...so when I order my rings I will need a set that are +.020 is that correct? also I will be honing the cyl...does that typically remove...

So on my 84 22r rebuild I don't know what type cam I have...is there ANY way to figure it out, Ive been reading and it appears that the CompCam 252S is a good replacement over stock cam but I don't know if I even have a stock cam...how can I figure this out.... The odometer shows 184,000 mi but...

Anyone know of a good manual or diagrams that show wire harness clip locations and styles used on the 84' Toyotas, I have a pickup SR5 That I'm completely stripping , ....also bolt and nut hardware sizes for mounting stuff in the truck. I plan on replacing any of the bolts nuts and harness...

So I pulled my 22R for truck renovation from my 1984 Toy Pickup SR5....Send My Tranny to the rebuild and the Trans shop calls me and says the parts they ordered for my 1984 Tranny are not fitting and they ask me If Im sure it an 84..?? Well according to the title and registration its an 84, so...

I am looking for FSM for my 84 Toy pickup 4X4, I cannot seem to find any out there...everytime I THINK I found one it's BS and has nothing to do with the vehicle. any LEGITIMATE assistance would be greatly appreciated. (No I don't want a common maintenance manual avail at local stores I got...

I'm trying to remove engine (22R) from the truck (1984 Toy SR5 Pick up).... Ive disconnected the tranny...removed all bolts and exhaust and two front engine mounts but the engine will not separate from tranny?????YES I got all the bolts out...:( any ideas folks. I am not taking tranny out with...

New to the Forum...I am under way now with striping my 84 Toy pick-up (184,000 miles) for complete renovation, presently pulling the motor/Tans , after which all componants under hood and on exterior will be pulled to get the shell prepped and painted, I will be rebuilding the engine and will...